27
Aug
Engine. Bleeding of Seastar outboard hydraulic steering systems Set-up a gravity feed steering fluid fill bottle Cut the bottom off an empty SeaStar steering fluid bottle.
425 turns from lock-to-lock.
Sea star hydraulic steering bleeding instructions. Bleeding instructions included with the liquid tie bar valve. Hydraulic Oil Requirements 2 bottles 2 quarts or liters for single station and single cylinder systems. 1 additional bottle for each additional helm cylinder or auto pilot.
Oil can be re-used if filtered through a fine mesh screen such as used for gasoline. Bleeding of Seastar outboard hydraulic steering systems Set-up a gravity feed steering fluid fill bottle Cut the bottom off an empty SeaStar steering fluid bottle. Securely mount or hang the bottle upside down above the highest helm on the boat.
Absolute easiest way to bleed seastar uflex hydraulic steering system - YouTube. In this video is how to check the level and bleed a Sea Star outboard hydraulic steering system. Bleeding a hydraulic system is purging it from air.
HYDRAULIC STEERING Proper fluid level set can be obtained by opening right bleeder and turning steering wheel to the right until fluid level reaches top of plastic filler fitting and then turning wheel one more full turn. CAUTION For unbalanced cylinders the fluid level in the helm must be set with the cylinder rod fully retracted. Holding the engine over to the right starboard and with a suitable container under the left port hand bleeder valve turn the steering wheel clockwise starboard until 10-20 seconds of air-free fluid has escaped from the bleeder then close the bleeder.
While continuing to turn the wheel close the left side bleeder. Important Notices Hydraulic and Optimus Steering. Controls.
Electronic Power Steering Manuals. Engine. Jackplate Installation Manuals and 3D Files.
Controls and Cables Mechanical Steering. The SeaStar helms are the smoothest and most efficient hydraulic steering systems available. They have been designed for normal pleasure and commercial boat use where standard rigging arrangements are used.
Before proceeding with the installation read these instructions thoroughly. Teleflex cannot accept responsibility for installations. Confirm that the steering cylinder can be fully stroked in both directions without stretching chafing rubbing andor kinking of the hydraulic hoses.
Where required confirm that extruded nylon tubing has NOT been substituted for SeaStar Steering Hose. DO NOT use a wire coil type trim switch with a hydraulic steering. Hydraulic Power Assist for SeaStar Steering Systems Including.
B ef o re you do it y o ur w a y pl e a se try it o u w a 172 INSTALLATION INSTRUCTIONS AND OWNERS MANUAL. Turn the boat steering wheel to the starboard side thus pumping air and steering fluid out of the bleeder fitting Step 12. When you see an air free stream CLOSE the bleeder nipple.
By following the above instructions you can ensure that you have properly bled the SeaStar hydraulic steering. 3905 Investment Lane Rivera Beach 33404 Florida. 561 863 7444 John Had him repair two of my helms they now look brand new and work great Prices are soso but alot cheaper than purchasing a new helm worth the callgood luck.
The SeaStarBayStar Steering System is the smoothest and most efficient hydraulic steering system available today. They have been designed for normal pleasure and commercial use where standard rigging arrangements are used. Before proceeding with the installation of this tilt helm read these instructions thoroughly.
Rinse off steering system thoroughly using fresh clean water only. - Cleaning fluids containing ammonia acids or any other corrosive ingredients MUST NOT be used for cleaning any part of the hydraulic steering system. Maintain steering system at a minimum of twice per year.
- See Maintenance on page 41 of this manual. That wont complete the job. You MUST do the following before opening any bleeder valve.
Turn wheel to right until motor stops turning. Then open bleeder on right side of cylinder prevent the motor from moving and turn the wheel in the opposite direction until there are no bubbles visible. Steering control and comfort.
It is suitable for use with high-performance propellors and jack plates. FEATURES Patented steering lock valves. Low friction hydraulic steering system.
425 turns from lock-to-lock. Compact helm has only a 4-716 footprint needs only 3 dash hole tilt requires larger hole. Optional SeaStar Pro.
From moving turn the steering wheel counter-clockwise until a steady stream of air free oil comes out of the bleeder. 12 bottle of oil or as required. Do not use anything other than your hands to restrain the cylinder bodyrod.
While continuing to turn the wheel close the right side bleeder and let go of the cylinder bodyrod. The Cylinder Attachment connects onto the bleed fittings with a simple push and click. Will not leak during bleed process.
The G2 Kit comes with full warranty and tech support to help with any questions. Not recommended for steering systems with integrated Power AssistPower Steering and or Auto Pilot components Made in the USA. Bleeding of Seastar outboard hydraulic steering systems Set-up a gravity feed steering fluid fill bottle Cut the bottom off an empty SeaStar steering fluid bottle.
The SeaStar Hydraulic Steering System is designed to provide that extra margin of muscle when needed and easily handles Outboard Sterndrive and Inboard engines in boats up to 50 feet. System selection installation and service is substantially simplified with just three major components.