25
Jan
Safe enough for aircraft gelcoat. Removing gasoline stains from gelcoat.
Lightly blast the gelcoat so that the sand does not penetrate the fiberglass.
How to remove gel coat. Use a sandblaster to blast the gelcoat away from the fiberglass. Lightly blast the gelcoat so that the sand does not penetrate the fiberglass. Gelcoating is thin and can be easily sandblasted in a short time.
How to Remove Tough Stains from Gel Coat - YouTube. How to Remove Tough Stains from Gel Coat. Having tried sanding products for paint removal Ive found even stearate coated papers clog almost instantly due to heat buildup melting the coatings.
Sometimes this is advantageous. Ive found the best way to remove old coatings from timber weatherboard house sidings is to use a 115 or 125mm variable speed angle grinder with a flexible backing pad with super agressive 24 or 36 grit. As Wade demonstrates restoring fiberglass gel coat by hand is a four-step process.
Apply product to a simple kitchen non-scratch scrub sponge. Work in the product while wet by hand see product recommendations below video Polish until you dont feel any resistance. If you go with gelcoat you are going to have to sand about 30 of it off to get a good finish.
For that you will start with 80 or 100 and work your way down to. Clean the gelcoat surface with a cloth and fiberglass cleaner. Spray or apply the fiberglass cleaner onto the gelcoat surface.
Use a clean cloth or towel to wipe the surface and remove dust dirt and grime. Spend some time scrubbing off any stuck on dirt or stubborn grime from the gelcoat. Clean the fiberglass with soap and water and wipe it down with a rag soaked in acetone and immediately removing it with a clean dry rag.
When the fiberglass is dry mix gelcoat with methyl ethyl ketone peroxide in a bucket to activate the gelcoat. For small sections of fiberglass apply the gelcoat. Within 12 hours the paint will be simple to remove through the use of a pressure washer and a brush.
It is a lot less labor intensive to use a chemical stripper than it is to scrape off the paintwork with no chemical assistance. It could also lead to unintentional. Always wear rubber gloves this stuff is acid and use cheap chip brushes to apply.
This whole process on my inflatable took less than 10 minutes and requires NO rubbing. Simply apply with the chip brush and watch it eat away the stains then dilute and rinse clean with water. You can get gelcoat with wax or without in certain cases.
The wax or Sanding Aid is an additive that allows the gelcoat to dry tack-free. Its used on the final coat only. With gelcoat we recommend at least 2 coats.
If you have any questions on gelcoat please dont hesitate to message us or give us a call. -Kevin FGCI Customer Service. Removing glueadhesive from Gelcoat Sticky Stuff Remover.
Tin of spray on citrus based solvent. Safe enough for aircraft gelcoat. Spray on leave for 10 minutes old glue just wipes off.
Manufactured by MYKAL 01933 402 822 - I have a tin in my hand. 05 Feb 2006 092649. Removing glueadhesive from Gelcoat.
Yes you can use acetone to clean the gelcoat prior to application of VS721 however there are numerous reasons to use Boat Scrub instead. Acetone is intended for use during repair or construction of the fiberglass not for general maintenance. Regular use can also be damaging to the gelcoat.
Does acetone remove gelcoat wax. Remove wax on gelcoat. Use acid-based stain removers to remove mineral and organic stains.
A gel acid-based stain remover will work best to remove stubborn stains. Wear rubber gloves and eye protection before you apply the remover. Use a rag to swab the cleaner across the stain and then let it sit for 20 minutes.
Use a hose to rinse off the remover. Does anyone know the best paint stripper to remove a coat of Awlgrip that didnt kickharden properly. I bought some of the Dads Easy Spray stripper it works awesome only problem is I tested it on a small spot and it popped the gelcoat off.
No big deal because the spot I tested was small. Sand was added to the second waxed coat at about 4oz sand to 32oz gel. Catalyzed at 2 and added wax at 35 to 4.
Mixed the wax warmed slightlywith power mixer for 3 minutes. Temp of surface and area 72 during process. All other materials were the same temps.
Removing gasoline stains from gelcoat. Jump to Latest Follow 1 - 14 of 14 Posts. Joined Mar 7 2004 3431 Posts.
Discussion Starter 1. Washing hose and water for rinsing the first preparation step before the actual removal process. The safest way to remove clear coat without damaging the paint is to use a buffing compound or a specialized clear coat removing agent.
400 grit 800 grit 1000 grit 1200 grit. When removing a stain the objective is to eliminate the stain without damaging the gelcoat itself. Avoid using strong solvents such as MEK or acetone and abrasives such as heavy rubbing compound or worse sandpaper.