How do i cut a hole in a propane tank without blowing it up

Basically you drain the tank and flush with plenty of water and then hook a car exhaust to a steel flexible pipe and run exhaust into the tank for several minutes to purge the tank then start cutting after checking with gas detectorMy cousin kept the exhaust running into the tank while he cut or welded because he said the exhaust had carbon monoxide in it and. Try using either of these methods in conjunction with some other cutting method like a sawzall.

I watched a pro cut up a 15000 gallon tank by removing all valves putting a spray end from an air compressor running full blast in the upper left hole and letting it drain out the lower right.

How do i cut a hole in a propane tank without blowing it up. I show how to easily remove a valve from a propane tank and cut the tank open without blowing up. A basic video showing how to open an old propane tank to make it into something else. Purge the tank again to ensure all propane gas has been removed.

To do this fill the tank with water through the fill valve the tank should be sitting level while this is being done. The tank should be so full of water it is running over the sides. Repeat this process twice before attempting to cut the tank open.

Fill with water again and let set overnight empty and cut. Gas does get into the pores of the metal so it will sputter when you cut it. I watched a pro cut up a 15000 gallon tank by removing all valves putting a spray end from an air compressor running full blast in the upper left hole and letting it drain out the lower right.

It ran for 24 hrs. In this video by Joe Baker find out how you can cut an empty propane tank without blowing yourself up. This can be a very dangerous project so proceed with extreme care.

Fill the tank with water as an extra precaution. It helps clear out gas residue in the tank. Thank you for watching.

Propane is heavier than air. Remove all valves and turn tank upside down for a couple of days. There might still be a smell coming from the tank but the gas will have evacuated the tank.

Ive cut thousands of propane tanks open over the past 20 years. Cut the tanks with water in them holding the level as high as possible. Cut just above the water line.

Try using either of these methods in conjunction with some other cutting method like a sawzall. To walker mixing air into the propane tank gives you 2 of the components needed in the triangle needed for an explosion the other componant is the torch used to cut the tank open You may have used this method in the past and got lucky enouph to remove enouph of the propane However this is not a safe way by any standards. They have what is called freon.

I use the 30 lb. Just make sure there is a hole in the soft plug. Also places that sell party supplies have helium for blowing up balloons.

Same type of tank only smaller and come in a bunch of bright colors. Again punch a hole in the soft plug. Do not rely on the valve being open.

Always fill the tank with water and rinse it out good. Then AS you weld on it have an inert gas like Nitrogen or CO2 flowing into the tank. PropaneLPButane vapors or heavier than air so if you simply take the valve off the top of the tank the vapor will remain in the tank for a very long time.

Basically you drain the tank and flush with plenty of water and then hook a car exhaust to a steel flexible pipe and run exhaust into the tank for several minutes to purge the tank then start cutting after checking with gas detectorMy cousin kept the exhaust running into the tank while he cut or welded because he said the exhaust had carbon monoxide in it and. You do NOT cut into the tank until it has been tested with a calibrated LEL monitor and reads 0. By RonG Date 07-12-2010 1529 Edited 07-12-2010 1532 Oh shucks just open all valves and vents put it out in 40-acre field uninhabited and throw Hand grenades and Molotov cocktails at it until you cant throw no more if you got a hand held Rocket launcher try that too.

There is only one simple and efficient way to get rid of all the remaining gas. Fill the cylinder with water until its full. The water will expel the gas and be replaced with fresh air.

Obviously do it OUTSIDE or youll get propane in your homeworkshop. I simply cut a hole in the outdoor rug right where the firepit sits. Then I fished the hose through that hole and under the outdoor rug to the place where I wanted to the propane tank to eventually sit.

After that I cut another hole under the propane. This advise was given to me and done by the local refilling station. Try disconnecting the tank for a couple mins.

If that doesnt work take the tank. Well i got the bottom off the propane tank today and did it like i said i was going to do except i used my portable band saw to cut it with instead of the gas powered saw when done i took a rag with some gas on it light it on fire and droped it in the propane tank with a long handle and there was no fire except the gas on the rag so i. How to Cut Open a Propane Tank without Blowing Yourself U.

Some cutting and welding is involved but the end result is durable and functional. 14- Make A Smoker Out Of 250 Gallon Propane Tank. Build a custom bbq smoker from a 250.

Lets see how to empty a propane tank on your next trip safely. In most cases it is unlikely to take more than a couple of minutes. Disconnect the tank s from their attachments and take them in an outdoor place or a well-ventilated indoor area where there is no source of ignition.

If you wash it out and keep it filled with water while cutting ie keep your cutting path at the apex as much as possible gas can leach out of steel over time so washing it and immediately cutting is preferable to leaving if for weeks if you are still concerned then get an inert gas such as argon for a mig and purge the tank does the same thing displaces the oxygen so. This could blow a hole in the gas tank and cause the release of fumes. You could heat the gasoline up to a high enough temperature that it could ignite spontaneously.

Without even a spark. Disposal Instructions for Coleman Propane Cylinders with the Green Key tool In 2009 The Coleman Company included a Green Key tool with each of our propane canisters. We used the Green Key program as a way to increase empty propane canister recycling.

Unfortunately the program was not accepted by many recycling agencies across the country. If you do end up with a fire that s threatening more than your meal don t hesitate to call the fire department the fire officials advised. If you can safely turn off the propane valve do it but if you have any doubt at all Get back and call the fire department said Card-Griffin.

Used correctly propane grills are safe.