Boat fuel tank pickup tube removal

Fixing The Moeller Fuel Pick Up Tube Rot Problem. The tank is 6 12 deep per engineering drawing and the tube part of the replacement is 6.

I think I have narrowed my boat engine trouble down to the gas tanks fuel pickup.

Boat fuel tank pickup tube removal. How to remove fuel pick up tube from plastic tank i just did this to my boati dissconnected fuel linethen took off the fuel valveto allow room for pick-up tube to come outvalve would have hit edge of access hole hold the square block still with an open end wrench in the vertical possitionthis will help keep the plastic tank from flexing. Mine was 34 inchthen. This is not an easy task given the cramp conditions and how stubborn the piece is to replace.

It may also help to spray the fitting with WD-40 or another sol. Tank pickup tube removal. You shouldnt crack the tank removing the fittingif it was corroded in you may have to remove the tank to remove the remnantsheat can help but its fuel so extreme care is neededrepeated soakings with PB.

Working on son-in-laws Jet boat about 25 years old. Steel tanks 2 Chevy 454 Electric Fuel pump wtank selector switch New hoses fittings We are unable to maintain fuel pressure from one tank. We have found no air leaks and suspect a holecrack in the pickup tube.

We have been told you can remove the pickup tube but we dont see how. Fixing The Moeller Fuel Pick Up Tube Rot Problem - YouTube. Fixing The Moeller Fuel Pick Up Tube Rot Problem.

If playback doesnt. I recently replaced the pickup tube on my 2002 1720CC. The old tube was cut on opposite sides at a 45 angle and had a screen inside the tube at its end.

I suppose the theory was that if jammed against the tank bottom it could still obtain fuel. The tank is 6 12 deep per engineering drawing and the tube part of the replacement is 6. Replacing A Boat Fuel Tank Part 1.

I took a differant approach. I removed the whole brass plate with pickup tube and screen. I then put the boat on the travelift very carefully tilted the boat bow up until every drop of fuel was at the rear of tank visiable from the plate stuck comericial vacuum cleaner diesel fuel soil never had gas in tank made a new pickup tube with same screen density but deeper 14.

About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy Safety How YouTube works Test new features Press Copyright Contact us Creators. Sep 7 2012. Yes the tube is generally welded in and is solid.

Since that tank is 22 years old it is probably time for a replacement. I dont know if it is worth it or advisable to attempt a repair. Clean in tank pickup or strainer - YouTube.

Way back when we were having fuel problems with our diesel read the full story here we removed one of the 18-gallon Tempo TP-18-T tanks in our Gemini catamaran and wanted to pull the fuel pickup tube to see if it was cracked. There is a screen inside the fuel pickup tube. Youll need to get the tube out in order to remove it.

The tube is cut on an angle at the bottom. Maybe you could even stick a wire down the pickup tube to push out the screen. I dont see where the screen on the bottom of the tank would obstruct the fuel pickup tube or any part of the system.

I think I have narrowed my boat engine trouble down to the gas tanks fuel pickup. I have replaced gas lines cleaned both carbs out replaced bulb replace fuel pump. It still will run for 20-30 secs then run out of gas the bulb goes loose not holding the prime.

I have been told air is getting in the line somewhere. HandymanHerb wroteGo within a 14 inch you want it to pick up all the fuel but still leave a little room for water to go. Most users face problems related to boat gas tank vents.

But most reported that it is comparatively an inexpensive problem to troubleshoot. In most cases replacing the vent and removing the kink of the fill line worked. Customers suggest keeping carb cleaner will come in handy in fixing such issues every time.

37 out of 5 stars. Boat Motor Elbow Tubing and Fuel Connector Kit Pickup Pick Up 3C7-70155 3B2-70155-0 M 823532A1 For Tohatsu Nissan Mercury Marine Outboard NS F 6HP - 98HP - 90HP 24-stroke Engine. 46 out of 5 stars.

Like stroken suggested soak it in PB blaster or something similar and let it set before you attempt to torque it loose. Ive never replaced an elbow on a poly tank like yours but I have replaced the same pickup elbow on an Aluminum tank. The pickup elbow screwed into a fitting that attached to the pickup tube in the fuel tank.

Mercury Mercruiser Quicksilver Oem Part 22-823531A 1 Conn Kit-Fuel-32 this has the elbow that screws into the top of the tank and the pick up tube and filter screen-ebay was 20 shipped Attwood 8838US6 Universal Sprayless Connector with Thread Sealant Amazon ASIN B007G2JFBA-907. Fuel Withdrawal 4 to 24 depth Standard Universal Boat Gas Tank Pick Up Tube 1988. Evinrude Johnson OEM Metal Gas Tank Replacement Cap 377536 388938 763525 1799.

Gas Tank Gasket 125530 305867 310984 332403 Evinrude Johnson 6 gallon Fuel OMC 999. 3 Gallon EPA Compliant Outboard Boat Motor Fuel Gas Tank Universal 3995. John has said it in a nutshell.

Biggest issue is in figuring out the dimensions of the cut out. The repair of the cutout is compounded by the damage you did in cutting the tank out. Last year my son fixed a fuel tank that Boat Country cut removing the floor for access to the tank.

They cut into the corner of the tank. The pickup tube was permanently installed we called the tank manufacturer to confirm this so we did not remove it to check it for blockages or cracks. Our fuel polishing made no difference.

Some Westerbeke literature said we. Buy Boat Marine Fuel Tank Pickup 12 x 38 ID Pickup Tube with 14 NPT Aluminum Fitting. When designing for a fuel polishing system I definitely wanted to get my polishing pick up directly over the deepest part of the tank in order scrubpolish every last little bit of the fuel.

This pick up tube is 18 off the dead bottom of the tank and directly over the V where any crudbugsalgae or other junk would naturally wind up.